1.Arming with Sound and Light
While the alarm is disarmed, press button once on the remote control, the siren will chirp once,
the direction lights will flash once, the remote control will beep once, and the system will arm 2
seconds later. The LCD Icons will display as picture (1).
2.Silent Arming
While the alarm is disarmed, press button once on the remote control, the direction lights will flash once, the remote control will beep once, and the system will enter silent armed mode 2 seconds later. The LCD Icons will display as picture (2).
3.Motorcycle Locating with Sound and Light
While the alarm is armed with sound and light, press button once on the remote control, the siren will chirp 3 times, the direction lights will flash 3 times and the remote control will beep 3 times for locating the motorcycle.
4.Motorcycle Locating with Light
While the alarm is in silent armed mode, press button once on the remote control, the direction
lights will flash 3 times and the remote control will beep 3 times for locating the motorcycle.
5.Stop Alarm
When the siren is sounding after the system is triggered, pressing button or on the remote control will stop the trigger and return the unit to the armed state 2 seconds later.
6.Disarming
Press button once while the alarm is armed, the direction lights will flash twice, the siren will
chirp twice (the siren will not chirp while the system is in silent armed mode), the remote control
will beep twice and the system will disarm. The LCD Icons will display as picture (3).
7.Anti-hijacking
When a driver is hijacked during driving, he or she may press and hold button for 3 seconds
within the transmission range of the remote control, the direction lights will flash once and the
remote control will beep 3 times. After 10 seconds, the siren will sound, the direction lights will
flash rapidly, the engine will stop and be immobilized and the remote control will beep
continuously. To exit anti-hijack mode only by pressing button
8.Remote Engine Start
While the alarm is armed or disarmed, press and hold button , the system will enter engine start
mode 3 seconds later, the remote control will beep 3 times. After the engine is started
successfully, the remote control will beep 3 times again. The LCD Icons will display as picture (4).
If your motorcycle does not start on the first crank it will automatically attempt to start up to 2
more times. If the 3 cranks all failed to start it indicates the battery level of the motorcycle is low
and you should recharge or replace your battery. Once the motorcycle is started, it will run for 8
minutes then shut down and return the system to the armed state. While the motorcycle is running
during remote start operation, you may press button once to stop the engine, the siren will
chirp twice and the remote control will chirp twice to confirm.

Special Remarks: When you operate the remote start function, please do not let the rear wheel of
the motorcycle touch the floor to avoid an accident.
9.Sensitivity Adjustment
There are 4 grades of sensitivity of the shock sensor trigger. The higher grade of the sensitivity
the more sensitive of the sensor trigger. The sensitivity grades will display as picture (5) on the
LCD Screen.
The first grade indicates the sensor trigger is turned off, i.e., the sensor trigger function is
disabled.
Please follow the following steps to set the sensitivity grade.
While the alarm is in silent armed mode, press and hold button for 3 seconds, the direction
lights will flash and the remote control will beep, the flashing and beeping times will be equal to
the grade of the sensitivity. Every time when you press and hold button for 3 seconds, the
sensitivity grade will be changed once. After you get an ideal sensitivity grade, press button
once to lock the sensitivity grade. The factory default setting is grade 3.
10.Shock and tilt Sensing
If the alarm is triggered by shock/titl sensing, the siren will chirp 5 times (the siren will not chirp
while in silent armed mode), the direction lights will flash 5 times and the remote control will
beep for 15 seconds. If the alarm is triggered again by shock sensing within 15 seconds, the siren
will sound for 15 seconds (the siren will not sound while in silent armed mode), the direction
lights will flash for 15 seconds and the remote control will beep for 15 seconds. The LCD Icons
will display as picture (6).

11.Ignition Trigger
When the ignition key is turned ON while the alarm is in any armed mode, the siren will sound
and the direction lights will flash continuously. If the ignition key is not removed within 15
seconds then the alarm cycle will repeat. The LCD Icons will display as picture (7).
12.Trigger Memory
If the alarm is triggered while it is armed, the siren will chirp and the direction lights will flash 4
times when pressing button to disarm the alarm.
13.Auto Rearming
Press button to disarm the alarm while armed, if you do not turn the ignition key to ON position
within 60 seconds then the system will rearm automatically.
14.Auto Arming (Selectable)
If the user does not arm the alarm with remote control 60 seconds after the ignition is turned off,
the system will arm automatically and enter the silent armed mode.
15.Power Interrupted Memory
When either or both constant [+] power and/or [-] ground is disconnected and then later
reconnected the system shall always power back up in the exact same mode it was in before the
power was disconnected.
16.Programmable Features
To Enter Programming Mode
While the alarm is disarmed, turn the ignition key to ON & OFF 3 times then stay OFF, then press
the Override Switch 5 times within 10 seconds, the siren will chirp once and the system will enter the programming mode. If you want to exit the programming mode, turn the ignition key to ON &
OFF once or wait for 10 seconds, the siren will chirp 3 times and the system will exit the
programming mode.
a)The Programming of the Pressing Times of the Override Switch When Performing
Emergency Override
While the alarm is armed, if the remote control is lost or it does not work, you may disarm the
system by pressing the Override Switch. The times of pressing the Override Switch can be set by
the user from 3 to 31 times. The process is as following:
While the system is in programming mode, press and hold button for 3 seconds, the siren will
chirp twice and the system is ready for programming the pressing times of the Override Switch.
Press the Override Switch, each time when pressing the Switch, the siren will chirp once. The
user may set the pressing times by himself or herself, for example 8 times, then he or she should
press the Switch 8 times. 10 seconds after this programming the siren will chirp 4 times to
confirm. The factory default setting is 5 times. It is recommended to set the pressing times again
to ensure the security of your vehicle.
b)Remote Control Programming
For security of your motorcycle please erase the codes of the lost Remote Control from memory
then learn all the Remote Controls again and this will prevent the illegal user who obtained the
lost Remote Control from using it to operate the alarm system. The process is as following:
While the system is in programming mode, press the Override Switch 5 times, the siren will chirp
once, indicating the codes of the remote controls memorized have been erased. Within 5 seconds

after deleting the codes, press button on the remote control to be learnt, the siren will chirp
once to indicate successful learning of the no. 1 remote control. Then press button on the no. 2
remote control to be learnt, the siren will chirp once to indicate successful learning. Follow the
above operation to learn all the remote controls. 10 seconds after completion of the learning, the
siren will chirp 3 times and the system will exit the programming mode. Or after completion of
the learning turn the ignition key ON then OFF the system will also exit the programming mode.
The system is designed to memorize codes of 2 two-way LCD Remote Controls and 4 one-way
Remote Controls.
Note: Please be noted that there should not be strong radio frequency around during the learning
process or the learning will be affected or fail.
c)Auto Arming ON/OFF Selection
While the system is in programming mode, press and hold the Override Switch for 5 seconds. If
the siren chirps once and the direction lights flash once, this indicates auto arming is ON. If the
siren chirps twice and the direction lights flash twice, this indicates auto arming is OFF. The
factory default setting is auto arming OFF.
17.Emergency Override
While the alarm is armed, turn the ignition key to ON & OFF 3 times then stay OFF, the siren will
sound, then press the Override Switch for the preset times (for example 8 times), the system will
disarm 5 seconds later and the motorcycle can now be started. If the user does not turn on the
ignition then after 60 seconds the system will enter silent armed state. After emergency override,
the user can arm the system by pressing button or .Special Remarks: The Override Switch should be installed in a hidden location where it is
convenient to operate.
18. Button Functions
a)LCD Illumination
If you want to know the status of your motorcycle at night, you may press and release button
on the remote control, the LCD will illuminate for 3 seconds.
b)Remote Control Vibrate Mode On/Off
While the alarm is armed , press and hold button for 3 seconds. The remote control will
beep once for vibration mode ON, twice for OFF. The factory default setting is vibration mode
ON. Programming vibration mode ON will decrease the life expectancy of the battery.
19.Remote Control Battery
The Remote Control is powered by a 1.5V type alkaline battery. When the battery is new, the icon
will display on the LCD screen. When the power of the battery is exhausted, the icon on the
LCD will flash and a new battery should be replaced. The LCD Icons will display as picture (8).

We ship our products to worldwide!

Shipping fee for all other countries please contact us:info@samitoelectronics.com